These popular supplies are compatible with Cleanmax CM-WAV Wide Area Vacuum
[products skus="90701"]HANDLE AND MAIN BODY schematic and parts book for Cleanmax Model/s CM-WAV
HANDLE ASSEMBLY schematic and parts book for Cleanmax Model/s CM-WAV
| Key | Part # | Part Description |
| 1 | 33189 | Box, Switch Top |
| 2 | 33190 | Switch Box Bottom |
| 3 | 19829 | Handle Main-steel Tube |
| 4 | X1039 | Switch, Momentary On/Off |
| 5 | 33452A | Handle Harness |
| 6 | 19849 | Trigger, Brush Switch |
| 7 | 33108 | Circuit Breaker 2.5 Amp |
| 8 | 19990 | Circuit Breaker 15 Amp |
| 9 | 32966 | On/off Switch |
| 10 | 33191 | Strain Restaint |
| 11 | 33203 | Conduit Nut |
| 12 | B207-0400 | Handle Decal |
| 13 | 1978 | Screw 1/4-20 X 1-1/2 |
| 14 | 16924 | Screw # 6-32 X ¾ |
| 15 | 3261 | Screw #10 32 X 3/8 |
| 16 | 11007 | Tooth Lock Washer |
| 17 | 19798 | Bracket, Grooved Handle |
| 18 | 5769 | Screw #8-32x5/8” |
| 19 | 30074 | Nut-hex.lock # 8-32 |
| 20 | 33102 | Handle, Cam Lever |
| 21 | 33103 | Washer, Cam Lever |
| 22 | 33104 | Metal Stud, Cam Lever Handle |
| 23 | 33105 | Hinge Pin, Cam Lever Handle |
| 24 | 33106 | Metal Washer, Cam Lever Handle |
| 25 | 33102-KIT | WAV Cam Handle Kit |
AGITATOR ASSEMBLY schematic and parts book for Cleanmax Model/s CM-WAV
| Key | Part # | Part Description |
| 1 | 19870 | Brush Roller assembly |
| 2 | X1298 | Brush Roll Assembly WAV N0 Shoe Or Pulley |
| 3 | 19808 | Axle Brush Roller |
| 4 | 19811 | Brush Roll |
| 5 | 11276A | Screw 1/4-20 X 7/8 W/ Adhesive Patch |
| 6 | 19848 | Guard Thread |
| 7 | 7535 | Screw #8-15 X 3/8 |
| 8 | 19809 | Bearing |
| No Shown | 7858 | Finger, Spring |
| 9 | 19805 | Block, Bearing Brush Alum |
| 10 | 32896 | Gasket 3/16 X 1/2 X 3 |
| 11 | 19810 | Shoe Brush Mount |
| 12 | 30077 | Gasket-Shoe Mount |
| 13 | 16142B | Screw #10-32 X 1/2 |
| 14 | 19804A | Pulley Brush Drive |
| 15 | 2011 | Screw-Set 1/4-20 X 5/16 |
Brush Motor schematic and parts book for Cleanmax Model/s CM-WAV
| Key | Part # | Part Description |
| 1 | 32369 | Brush Motor Assembly |
| 2 | 19836 | Mount Brush Motor |
| 3 | 33061 | 25a Rectifier |
| 4 | 33451 | Screw, 10-24 X 5/8” |
| 5 | 33197 | Motor 3.25 Dia. .25hp |
| 6 | 86 | Screw 1/4-20 X 1/2 |
| 7 | 7CY002 | WASHER-LOCK |
| 8 | 14142 | Washer-plain .265 Id |
| 9 | 19835 | Pulley Brush Drive Motor |
| 10 | 2011 | Screw-set 1/4-20 X 5/16 |
| 11 | 3660 | Screw #10 24 X 7/16 |
| 12 | 10892 | Nut Hex.Lock #10, 24 |
| Not Shown | 33503 | Harness, Wiring Wav ( part of 32369 motor assembly) |
| Not Shown | 15200 | Terminal Ring #10 X 22/18GA ( for motor ground wire) |
| Not Shown | F21 | Terminal Rring #10 14-16 AWG ( for harness ground wire) |
Motor schematic and parts book for Cleanmax Model/s CM-WAV
| Key | Part # | Part Description |
| 1 | 30092 | Vac Motor Wav |
| 2 | 30090 | Gasket |
| 3 | 19834 | Filter Intake |
| 4 | 33107 | Worm Gear Clamp 6” |
| Not Shown | 30620 | Screw #10-16 X 3/4 ( Motor mount- ing screws) |
Report errors on this page HERE
